Page updated · Independent public directory · Last reviewed November 16, 2026 · Not a government agency · By Bill Dahlstrom

Blue-Green Stains from Water: Copper and Corrosion

Blue-green stains are copper dissolved from your own pipes by corrosive water, and the same water can pull lead from older solder and brass.

Causes and fixes
CauseHow to tellFix
Corrosive well waterStains on a well, often a new one.An acid neutralizing filter, or a soda ash feed, where the water enters the house.
Corrosive city waterStains on water from a utility.Start with your utility, not a filter. Tell them about the stains and ask for a lead and copper test.
A water softenerThe stains started after a softener went in.Do not run it on new copper plumbing for the first few weeks.
Lead from the same pipesNone. You cannot see, taste, or smell it.At the tap you drink from: a pitcher or faucet filter certified to NSF/ANSI 53 for lead, or reverse osmosis certified to NSF/ANSI 58 for lead, which also removes copper.

To be sure before you spend, test first. Find the free or low-cost public test in your state, then enter your numbers on our results page to see what each one means and what fixes it.

Copper from your plumbing

Penn State Extension says: "Copper has a secondary drinking water standard of 1.0 mg/L because it causes a bitter, metallic taste to water and a blue-green stain in sinks and bathtubs."1 Past the stain, EPA lists this health effect for copper: "Short term exposure: Gastrointestinal distress".2

The copper is rarely in the water before it reaches your house. The Minnesota Department of Health says: "Copper is not usually found in the groundwater that feeds your well. Copper may enter your drinking water as it travels through your plumbing system."3

Corrosive water

Water that dissolves metal is common. USGS says: "A new U.S. Geological Survey assessment of more than 20,000 wells nationwide shows that untreated groundwater in 25 states has a high prevalence of being potentially corrosive." "Signs of corrosive water causing leaching of metals may include bluish-green stains in sinks, metallic taste to water, and small leaks in plumbing fixtures."4 Two changes at home can start it, or make it worse.

  • A water softener. Among its downsides, the Minnesota Department of Health lists: "Can corrode your pipes. The corroded metal from the pipes can end up in your water. This can contribute to elevated lead and copper levels in drinking water." "If your home has new copper plumbing, do not run the water softener for at least the first few weeks you use water at your house."5
  • A new well. The Minnesota Department of Health says: "Be aware that the water from the new well may dissolve copper from your plumbing."3

Lead in the same pipes

USGS says: "Potential sources of lead in homes include:"4

  • "lead solder used in copper fittings in homes built prior to the late 1980s".4
  • "“lead-free” brass components, which, in all states, except California, may have contained up to 8 percent lead, prior to 2014".4

Lead leaves no visible sign. EPA says: "Since you cannot see, taste, or smell lead dissolved in water, testing is the only sure way of telling whether there are harmful quantities of lead in your drinking water."6 If the water also tastes like metal, our metallic taste guide covers that side. For what a lead number means, see lead water test results.

The first-draw test

A copper and lead test uses the first water out of the tap after it has sat in the pipes, and that is also how it tells your pipes from your well. Penn State Extension says: "Copper and lead concentrations are usually highest in the first water out of the tap since this water has been in contact with the plumbing for a longer time. Metal concentrations from corrosion will decrease as water is flushed through the plumbing system. If this doesn't happen, the source of the metals is most likely your well water itself."1 Follow your kit's own sampling instructions.

On city water, your utility samples homes for copper, but not necessarily yours. Of the federal rule, the Minnesota Department of Health says: "These systems have to take actions to reduce the amount of copper in the water if more than 10 percent of the water samples they take from homes and sampling sites served by the system have copper levels over 1,300 µg/L." "Remember that your home may have higher levels of copper in drinking water than the homes your public water system tested."3

53 public tests we list check for copper, and 4 of them are free. 114 public tests we list check for lead, and 20 of them are free. The public test link at the top of this page shows which ones serve you and what each costs, or see free lead test kits by state.

The fix

Every day, starting now. The Minnesota Department of Health says: "Let the water run for at least 30-60 seconds before using it for drinking or cooking if the water has not been turned on in over six hours."3 Use cold water for drinking and cooking. "Hot water releases more copper from pipes than cold water."3

On a well. Treat the water where it enters the house so it stops dissolving the pipes. Penn State Extension says: "Acid-neutralizing filters are very simple water treatment units that are intended to increase pH and add calcium, thereby decreasing corrosivity." "It is important to note that this process will increase the hardness of the water, but this is necessary for proper corrosion control." "Corrosivity can also be treated by injecting a sodium hydroxide or soda ash solution using a chemical feed pump before the pressure tank."1

On city water. Corrosion control is your utility's job. EPA says: "By controlling these factors, the public water system can reduce the leaching of metals such as copper, iron, and zinc from pipes or fixtures, as well as the color and taste associated with these contaminants."7

At the tap you drink from. This is the fix the results tool shows for a high lead number.

  • Pitcher or faucet filter. Pick one certified to NSF/ANSI 53 for lead and NSF/ANSI 42 for particulates (Class I). (EPA)
  • Under-sink reverse osmosis. Reverse osmosis removes lead. Look for NSF/ANSI 58 certification that names lead on the label. (CDC)

The small commission from purchases made through this link helps keep this free public directory open, at no extra cost to you.

Waterdrop G3P600 under-sink reverse osmosis system

Of the systems this site links, a certifier lists only this one for lead. Under-sink reverse osmosis. Waterdrop G3P600 (affiliate link). Waterdrop says "8-stage reverse osmosis system designed to reduce a wide range of common contaminants, including dissolved solids, heavy metals, chlorine, and other impurities for everyday drinking water." It is certified for lead under NSF/ANSI 58 (IAPMO R&T listing WC-13976, checked November 14, 2026).

Sources

  1. Penn State Extension, Corrosive Water Problems
  2. EPA, National Primary Drinking Water Regulations
  3. Minnesota Department of Health, Copper in Drinking Water
  4. USGS, New Study Shows High Potential for Corrosive Groundwater in 25 States
  5. Minnesota Department of Health, Home Water Softening Frequently Asked Questions
  6. EPA, Basic Information about Lead in Drinking Water
  7. EPA, Secondary Drinking Water Standards: Guidance for Nuisance Chemicals

Checked November 15, 2026.