Iron Water Test Results: What Your Number Means
EPA's guideline for iron is 0.3 mg/L, set for taste and stains, not health (EPA). Above it, the water is still safe to drink, cook with, and bathe in, but it can taste of metal, stain sinks and laundry orange or brown, and clog fixtures.1
Nothing has to happen this week. Before you buy treatment, find out which form of iron you have and test hardness and pH too, because the fix depends on them: a water softener for lower levels of clear-water iron, an iron filter for more, and air or chlorine with a filter above 10 mg/L.
Health
"Iron in water does not usually present a health risk."1 "Point of reference: Water with an iron level above 0.3 milligrams per liter (mg/L) is usually considered objectionable. Iron levels are usually below 10 mg/L in water."1
Forms of iron
The same number can need different treatment, so note what the water looks like.
- Clear-water iron. "Ferrous iron ("clear-water iron"): Water comes out of the faucet clear, but turns red or brown after standing."1
- Red-water iron. Red or yellow as soon as it leaves the faucet.1
- Organic iron. Yellow or brown, sometimes clear, more likely in very shallow wells or wells affected by surface water, and harder to treat.1
"In addition to testing for iron, it can be helpful to test for hardness, pH, alkalinity, and iron bacteria."1
Treatment by level
| Iron | What usually fits |
|---|---|
| Under 1.0 mg/L, dissolved | Catalytic carbon filter. "It is effective for concentrations of dissolved iron less then 1.0 mg/L."2 |
| Up to about 5 mg/L, clear-water | Water softener. "Manufacturers report that some water softeners can remove up to 10 mg/L. However, 2 to 5 mg/L is a more common limit. A manganese greensand filter can be effective for levels that are up to 10 to 15 mg/L."1 |
| Up to 10 to 15 mg/L | Iron filter such as manganese greensand, for clear-water or red-water iron.1 |
| Over 10 mg/L | "Aeration (injecting air) or chemical oxidation (usually adding chlorine in the form of calcium or sodium hypochlorite) followed by filtration are options if iron levels are more than 10 mg/L."1 |
Reverse osmosis or distillation removes any form of iron, but high iron plugs them quickly, so Minnesota points to whole-house treatment in that case.1
Common results
| Result | What it means |
|---|---|
| 0.1 mg/L | Under EPA's 0.3. No iron treatment needed. |
| 0.3 mg/L | At EPA's guideline. Minnesota calls water above this level usually objectionable. |
| 0.8 mg/L | Over the guideline. Expect orange stains. A catalytic carbon filter works on dissolved iron under 1.0. |
| 3 mg/L | Clearly over. A water softener can handle clear-water iron at this level, or an iron filter. |
| 12 mg/L | High. Past what most softeners handle; a greensand filter, or air or chlorine and a filter, fits here. |
| 300 µg/L | The same as 0.3 mg/L, in another unit. 1 mg/L is 1,000 µg/L. |
Example numbers. EPA limit for public water systems, shown for reference. Private wells are not regulated.
A filter we link
The small commission from purchases made through this link helps keep this free public directory open, at no extra cost to you.

This is the whole-house filter we link for iron. Whole house filter for iron and manganese. Waterdrop WHF21-FG (affiliate link). Waterdrop says "Whole house water filter WHF21-FG adopts iron and manganese reducing filter and GAC filter, five-stage filtration." Waterdrop says it reduces iron, but we found no independent certification for that.
None of the filters we link is certified for iron. Look for a filter that NSF, IAPMO R&T, or WQA lists for iron reduction, and check that listing for the exact model.
Test manganese too: it stains like iron and has health guidance. See manganese results, and brown or orange water if color is what you notice.
New to lab reports? How to read a water test report. Another number on your report? Check it in the results checker.
Sources
- Minnesota Department of Health, Iron in Well Water
- Penn State Extension, Iron and Manganese in Private Water Systems
Checked November 15, 2026.
